REBNY

REBNY rentable area & loss factor calculator

REBNY treats rentable area as a number the landlord declares, not one computed from geometry. Try the calculator below with a sample floor, or your own drawn usable area and loss factor — add-on factor, loss factor and target rentable area recompute from each other as you type.

RentableArea.com is not affiliated with or endorsed by the Real Estate Board of New York (REBNY) or BOMA International.

Status: supported — the calculator follows the owner's product rule (usable area, loss factor and rentable area as three mutually determining values) and REBNY's own usable-area definition. REBNY publishes no spreadsheet for this calculation, so there is no official worked example to reproduce.

REBNY — the Real Estate Board of New York — treats rentable area differently from BOMA: not as a figure computed from geometry, but as a number the landlord or broker declares. That changes what "checking" a REBNY rentable square footage figure actually means. The calculator below walks through that check on one NYC office floor; the rest of this page explains the REBNY rules behind it.

Try it: drawn usable area, loss factor and target rentable area

The floor-plan figures below are pre-loaded from a sample floor so you can see the calculator work immediately — turn on "Use my own figures" to type in your own drawn usable area, net usable area and retail area instead. Add-on factor, full-floor loss factor, multi-tenant loss factor and target rentable area recompute from each other live: change any one of the four and the other three follow the same public identity, rentable = usable ÷ (1 − loss factor).

Off: the floor-plan figures below are pre-loaded from a sample floor. On: type in your own drawn usable area, net usable area and retail area — office area is calculated for you.

From the floor plan sample floor

In the product these come from your drawing. Here they're a plausible sample floor, greyed out until you turn on "Use my own figures" above.

The floor's total usable area, drawn or measured under REBNY's rules — office area and retail area below are this total split in two.

This suite's own net usable area before REBNY's corridor apportionment — the input the multi-tenant loss factor below is measured against.

= drawn usable area − retail area. Derived, not an independent input — the add-on factor, full-floor loss factor and target rentable area below are measured against this office figure, never against the total drawn usable area.

Subtracted from drawn usable area to get office area above, then added back at 100% in the total below — REBNY measures store rentable area directly, with no loss factor, so retail never runs through the office fields below.

What you can change

Target rentable area ÷ office usable area.

Default 27% — market convention for NYC office space, not a REBNY-published figure.

The landlord-stated rentable area for this floor's office space.

Target rentable area (office)13,698.63 SF
+ Retail area (added at 100%, never loss-factored)640 SF
= Total target rentable area14,338.63 SF

Runs rentable = usable ÷ (1 − loss factor) — the public identity behind add-on factor and loss factor alike, applied here to office usable area (drawn usable area minus retail). Retail/store area is added at 100% and is not grossed up — REBNY's own rule. REBNY itself publishes no formula or default loss-factor percentage for office rentable area; the 27% default above is a market convention, labelled as such, never a REBNY rule.

REBNY's own published text names no loss-factor percentage anywhere — not 27%, not any other figure. The 27% shown above by default is a market convention compiled from secondary sources for NYC office space, not a value REBNY itself sets or recommends — change it to whatever figure your own lease or broker has quoted.

The implied ratio, and which figure is the denominator

Once you have both numbers, two different ratios are commonly quoted, and they use different denominators — mixing them up is the most common error in a REBNY check:

Load factor

Rentable ÷ Usable

A multiplier on usable area. Denominator is usable area. A load factor of 1.35 means the quoted rentable figure is 35% larger than the usable area you measured.

Loss factor

(Rentable − Usable) ÷ Rentable

The share of the quoted rentable figure that isn't your own exclusive space. Denominator is rentable area — the larger of the two numbers — so loss factor is always a smaller percentage than load-factor-minus-one for the same floor.

Single-tenant vs multi-tenant floor: the same check needs different inputs

On a single-tenant floor, one tenant's usable area is close to the floor's entire usable area, so a usable-area-vs-quoted-rentable check is reasonably direct. On a multi-tenant floor, REBNY's own method deducts the floor's corridor area (including toilets and supply rooms) and apportions it back across every suite on that floor, in proportion to each suite's own net usable area — not just the one suite you may have drawn or measured. Checking a single suite's own outline against a quoted rentable figure, without the floor-wide inputs REBNY's apportionment formula calls for (the floor's total corridor area and every other suite's net usable area), will not reliably reproduce the landlord's number — a gap there is not automatically an error, it may just mean the one-suite check is missing those floor-wide inputs.

An implied ratio is a check, not proof

A load or loss factor implied from your measured usable area and the landlord's quoted rentable area is useful: it tells you whether the quoted figure is in a plausible range for a floor like yours, and gives you a specific number to ask about. It is not, by itself, independent proof that the landlord's figure is wrong, or a reproduction of the full REBNY calculation for that floor — a lease dispute over square footage still needs the floor-wide inputs REBNY's own rules call for, particularly on a multi-tenant floor.

What REBNY actually deducts — and what it apportions

REBNY's own text works from a short, fixed deduction list, not a BOMA-style two-tier "common area" classification. Before any apportionment, REBNY subtracts public elevator shafts and their machine rooms, public stairs, qualifying HVAC equipment, fire towers, and main telephone/electric switchgear rooms — all with their enclosing walls — from every floor's usable area, single- or multi-tenant. On a multi-tenant floor only, REBNY additionally deducts the corridor area (including toilets and supply rooms) and apportions it back to each suite in proportion to that suite's own net usable area. REBNY's text does not name or define a "Floor Common Area" or "Building Common Area" category the way BOMA (ANSI/BOMA Z65.1) does — those are BOMA's terms, for a different method, named here only to contrast with REBNY's own deduction-and-apportionment language.

Retail doesn't go through the same pipeline

Under REBNY, retail and storage area is measured straight to its own rentable figure, with no loss factor applied — it never enters the office usable/rentable calculation at all. That's why the calculator above adds retail area at 100% on top of the office target rentable area, rather than running it through the add-on or loss-factor fields: REBNY produces office and retail/storage rentable area as two separately-produced figures, and its published text does not define a formula for combining them into one building-wide total.

See how to audit the square footage in your lease if a quoted loss factor doesn't match what your own floor-level check supports.

Frequently asked questions

Does REBNY compute rentable area the way BOMA does?

No. BOMA derives rentable area from measured geometry through a computed allocation ratio. REBNY standardizes usable area only; rentable area is instead a number the landlord or broker establishes, typically by applying a declared loss factor to usable area — REBNY's own text never publishes a formula or percentage for deriving it. That is why checking a REBNY figure starts from your own floor's drawn usable area, not from a formula that derives rentable area independently.

What exactly is an implied ratio, and what does it prove?

It's the relationship between a usable area you drew or measured yourself and a rentable area the landlord quoted — nothing more. Computing it tells you whether the quoted figure is consistent with a typical declared loss factor for that kind of floor. It does not, on its own, prove the landlord's number is wrong; see "a check, not proof" below.

Does this check work the same way on a multi-tenant floor?

Only with more care. On a single-tenant floor, the suite's usable area is close to the whole floor's usable area, so the check is fairly direct. On a multi-tenant floor, REBNY deducts the floor's corridor area (including toilets and supply rooms) and apportions it back across every tenant on that floor in proportion to each suite's own net usable area — so a single suite's own outline, without the floor's total corridor area and every other suite's net usable area, is not enough to establish that suite's usable area on its own.

Does REBNY classify common area the way BOMA does?

No. REBNY doesn't define a "Floor Common Area" or "Building Common Area" split — that two-tier classification is BOMA's (ANSI/BOMA Z65.1) own terminology, not REBNY's. REBNY instead works from a fixed list of building-service deductions (public elevator shafts, public stairs, qualifying HVAC, fire towers, main telephone/electric switchgear rooms) that come out of usable area on every floor, plus a separate corridor-area apportionment step that applies only on multi-tenant floors.

How does retail space factor into a REBNY building's total rentable area?

It doesn't go through the office usable/rentable pipeline at all. Retail and storage area is measured directly to its own rentable figure with no loss factor applied. REBNY produces office and retail/storage rentable area as two separate figures — its published text doesn't define a formula for combining them into one building-wide total.

See this standard applied to your own building

Upload a floor plan and RentableArea.com produces the area totals and load factor for you — no spreadsheet to build by hand.